Crystalfontz LCD Module USB Driver
CrytsalFontz Logo 1 CrystalFontz Logo 2. This driver supports the serial and USB interface alphanumeric display modules by Crystalfontz. The CFA product series are intelligent graphic LCD modules that offer USB and Serial interface, 6 button keypad, 4 status LED's and 5 GPIO. CFATML Features. Part Change Notice # CFA, CFA, and CFA displays with ATX (power on / off / reset) functionality enabled. Alphanumeric liquid crystal display modules with USB interfaces, manufactured by Crystalfontz America Inc. Modules of the series CF– (16 x 2 characters).
|Supported systems:||Windows All|
|Price:||Free* [*Free Regsitration Required]|
Crystalfontz LCD Module USB Driver
For this type of configuration, Crystalfontz LCD Module USB Monitor can send readings to an external alphanumeric liquid crystal display LCD which can be connected to the computer via USB interface. An example is shown in the following photo: LCD output example In addition to acquired readings from sensors and probes, Hardware Monitor allows you to specify additional data for output as well, for example the current time, or the IP address of a certain network interface.
The example above shows date and time, a bar graph for the load of 4 processor cores, a power value, a selected temperature, the S. The contents of the display is updated at the same rate as all other output channels of Hardware Monitor.
Hardware Monitor supports the following hardware equipment only: Alphanumeric liquid crystal display modules, following the original Hitachi HD industry standard. Modules Crystalfontz LCD Module USB the series CF— 16 x 2 characters and CF— 20 x 4 characters are supported. When attaching these devices, no additional Crystalfontz LCD Module USB drivers need to be installed. We cannot answer any questions about these hardware devices or their distribution.
We do not promote or sell these products.
X68 Graphic Display Module (CFATML) from Crystalfontz
Regarding any questions about building or configuring your own LCD output unit, please see the following web sites for documentation and contact information: Please contact the respective vendors Crystalfontz LCD Module USB additional information. We provide this only as a convenience to our users. We have not tested the information found on these sites and make no representations regarding its accuracy or reliability.
There are risks inherent in the use of any information or products found on the Internet, and we assume no responsibility in this regard.
The Best LCD Display for Your Project
Please understand that a third-party site is independent from us and that we have no control over the content on that website. Configuring display units Configuration of an external LCD unit is very easy and can be done by simple drag-and-drop operations. All detected USB units will be displayed in the small table at the top of the window. To select which Crystalfontz LCD Module USB of LC display is connected to each USB unit, click on a line in the table, then use the pop-up menu Configure selected USB device for display type to choose how many lines and columns are available on the display.
The LC Display will light up as soon as you switch the type menu from No display to one of the possible display Crystalfontz LCD Module USB. The following test patterns are available: This makes it easier to see which module is which when you are working with more than one device. This test allows you to verify if the display type setting is correct.
Modern versions of the chip may support different character sets when sold in different regions of the world. You might see accented European characters for example, or Cyrillic characters replacing Katakana in specific implementations of LCD units.
Kit Configurator - Crystalfontz Liquid Crystal Displays
After pressing it, a dialog sheet will open and you can set operating parameters as backlight brightness or display contrast. Just select the desired time or the value never with Crystalfontz LCD Module USB slider at Start backlight saver. In this case, communication to the LCD module will stop after the selected time interval. At that moment, macOS will no longer misinterpret the module as active user, and the standard sleep interval timers will start as expected.
Note that the total sleep timeout interval will be the sum of the LCD backlight saver time and the sleep time you have configured in the Energy Saver pane of System Preferences. LCD Module After the display type has been configured, you can use the lower part of the window to select which output elements should be sent to the display. The left table shows you all output elements which are available on the local Crystalfontz LCD Module USB.
The right table shows you the active elements which are currently being sent to the display. At the beginning, the right-hand table is empty. You can use the mouse, dragging elements from the left to the right table to configure the desired output step by step.